TP-Link TL-SG1008D 8-Port Gigabit Switch in Kenya

The TP-Link TL-SG1008D 8-Port Gigabit Desktop Switch is a compact unmanaged Ethernet switch designed for homes, offices, small businesses and workgroups that need additional high-speed wired network connections. It provides 8 × 10/100/1000Mbps Auto-Negotiation RJ45 ports, with Auto MDI/MDIX on every port for straightforward installation.

Compared with a Fast Ethernet switch such as the TL-SF1008D, which is limited to 100Mbps per port, the TL-SG1008D provides Gigabit Ethernet up to 1,000Mbps per port. This makes it much better suited to fibre internet, Starlink, NAS storage, office computers, NVRs, access points, smart TVs and other modern network devices.

The TL-SG1008D is also designed for plug-and-play networking, so no software configuration, controller or switch IP setup is required. TP-Link lists Green Ethernet technology, IEEE 802.3x flow control, desktop or wall mounting and fanless operation among its key features. 

TP-Link TL-SG1008D Key Features

TP-Link's official documentation confirms the eight Gigabit ports, flow control, Auto MDI/MDIX and plug-and-play design. A current Kenyan listing specifies 16Gbps switching capacity, 11.9 Mpps forwarding and 1.5MB buffer memory.

8 Gigabit Ethernet Ports

The TL-SG1008D provides eight 10/100/1000Mbps RJ45 interfaces. Each port automatically detects the capabilities of the connected device and negotiates the appropriate Ethernet speed. 

This backward compatibility allows both older Fast Ethernet devices and newer Gigabit equipment to operate on the same switch.

16Gbps Switching Capacity

The TL-SG1008D has a 16Gbps switching capacity, providing sufficient internal bandwidth for full-duplex Gigabit communication across its eight ports. 

The 16Gbps figure represents aggregate switch fabric capacity rather than the speed available to one device. Each individual Ethernet port supports a nominal maximum link rate of 1Gbps.

This provides substantially more network capacity than an 8-port Fast Ethernet switch.

11.9 Mpps Packet Forwarding

A current Kenyan specification lists the TL-SG1008D with a packet-forwarding rate of 11.9 million packets per second. 

This helps the switch efficiently move traffic between computers, storage devices, NVRs, access points and other connected equipment.

Plug-and-Play Installation

The TL-SG1008D is an unmanaged switch, meaning there is no complicated configuration process.

A typical network is:

Internet → Router → TL-SG1008D → PCs / TVs / Printer / NAS / NVR

Simply connect one Ethernet port to the router or gateway and connect your endpoint devices to the remaining ports.

TP-Link specifically states that the switch requires no configuration. 

Auto-Negotiation

Each port automatically determines whether a connected device supports 10Mbps, 100Mbps or 1Gbps.

For example:

100Mbps printer → 100Mbps

Gigabit desktop → 1Gbps

Gigabit router → 1Gbps

This eliminates the need to manually configure Ethernet port speeds.

Auto MDI/MDIX

All eight ports support Auto MDI/MDIX, eliminating the traditional need for crossover cables when connecting network equipment. 

In a typical deployment, any port can therefore be used for the uplink to the router.

IEEE 802.3x Flow Control

TP-Link lists IEEE 802.3x flow control for reliable full-duplex data transmission. 

Flow control helps connected devices manage temporary congestion by regulating Ethernet traffic when a receiving device cannot immediately process additional frames.

Store-and-Forward Switching

The TL-SG1008D uses Store-and-Forward switching, meaning Ethernet frames are received and checked before being forwarded toward their destination.

This approach is common in unmanaged desktop switches and provides reliable network operation without requiring manual management.

Jumbo Frame Support

Official TP-Link documentation for documented revisions lists support for 15KB Jumbo Frames. 

Larger Ethernet frames can improve efficiency in some LAN applications, particularly:

• NAS transfers

• Server-to-PC transfers

• Backup jobs

• Large multimedia files

However, every device in the communication path must support compatible frame sizes for jumbo frames to be useful.

Fanless Operation

The TL-SG1008D uses a fanless design, making it suitable for quiet environments such as offices, living rooms and reception areas. 

The absence of a fan also means there are fewer moving parts inside the switch.

Desktop and Wall-Mount Installation

TP-Link specifies both desktop and wall-mounting installation for the TL-SG1008D. 

This makes the switch flexible enough for use:

• On a desk

• Beside a router

• Under a counter

• On a wall

• In a small communications area

• Inside a suitable network cabinet

Green Ethernet Technology

The TL-SG1008D incorporates TP-Link's energy-efficient Ethernet technology.

TP-Link documentation states that certain revisions can reduce power consumption by up to 80% under specified test conditions. Actual savings vary according to link status, cable length and operating conditions.

This makes the switch suitable for continuous 24/7 use in homes and offices.

TP-Link TL-SG1008D for Home Networks

The TL-SG1008D is an excellent way to expand the number of wired Ethernet connections available from a home router.

A typical installation could be:

Router → TL-SG1008D → Smart TV + Desktop + Gaming Console + Printer + NAS

Unlike a Fast Ethernet switch, Gigabit ports provide much more bandwidth for streaming, backups, file transfers and modern high-speed internet connections.

TP-Link TL-SG1008D for Small Offices

The switch is equally suitable for a small business requiring wired connectivity for several devices.

Example:

Router → TL-SG1008D → PCs + Printer + NAS + NVR + Access Point

Eight ports provide enough capacity for a modest office while avoiding the size and cost of a larger 16-port or 24-port switch.

TP-Link TL-SG1008D for Fibre Internet

The TL-SG1008D is well suited to modern fibre internet connections.

Typical topology:

Fibre ONT → Gigabit Router → TL-SG1008D → Wired Devices

Because the switch supports Gigabit Ethernet, it avoids the 100Mbps bottleneck found on Fast Ethernet models.

For internet or LAN traffic above 1Gbps on a single connection, a 2.5GbE or faster switch should be considered.

TP-Link TL-SG1008D for Starlink

The TL-SG1008D is a practical switch for expanding a Starlink wired network where Ethernet connectivity is available.

Typical setup:

Starlink → Router/Gateway → TL-SG1008D → PCs / TVs / NVR / Access Points

Gigabit Ethernet makes the TL-SG1008D much more suitable for Starlink than the TL-SF1008D Fast Ethernet model, which can restrict wired throughput to approximately the 100Mbps class.

For business Starlink installations requiring VLANs, failover, centralized management or PoE access points, an Omada managed or PoE switch may be more appropriate.

TP-Link TL-SG1008D for NAS and File Sharing

Gigabit networking makes the TL-SG1008D useful for local storage.

Example:

NAS → TL-SG1008D → PCs

Compared with 100Mbps Fast Ethernet, Gigabit Ethernet offers up to ten times the nominal link capacity.

Actual transfer speeds depend on:

• Storage performance

• Network protocol overhead

• Computer hardware

• NAS capabilities

• Ethernet cabling

For small-office NAS systems, Gigabit switching is considerably more practical than Fast Ethernet.

TP-Link TL-SG1008D for CCTV

The TL-SG1008D can also carry traffic for IP surveillance equipment.

Typical setup:

Router → TL-SG1008D → NVR + IP Cameras

Gigabit Ethernet provides useful aggregate bandwidth when multiple camera streams are active.

However, the TL-SG1008D does not provide PoE.

If cameras require power over Ethernet, use compatible PoE injectors or a TP-Link PoE switch.

TP-Link TL-SG1008D for Access Points

Modern Wi-Fi access points can easily exceed 100Mbps of wireless traffic, making Gigabit Ethernet preferable for their wired uplinks.

Example:

Router → TL-SG1008D → Wi-Fi Access Point

The TL-SG1008D can provide the Gigabit data connection, but it does not provide PoE power.

For TP-Link Omada AP installations, a PoE switch may offer a cleaner installation.

TL-SG1008D vs TL-SF1008D

A simple TP-Link naming guide is:

SF = Fast Ethernet

SG = Gigabit Ethernet

For most new installations, the TL-SG1008D is the better long-term option.

TL-SG1008D vs TL-SG1005D

*Assuming one port is used as the connection to the router.

If you expect more than four wired devices, the 8-port model provides better expansion capacity.

TL-SG1008D vs TL-SG108

The TL-SG108 is another TP-Link 8-port unmanaged Gigabit switch.

The main practical difference is often chassis design and the exact hardware revision available.

TL-SG1008D vs TP-Link 8-Port PoE Switch

Choose a PoE model when you want one Ethernet cable to carry both network traffic and electrical power.

Does the TP-Link TL-SG1008D Support PoE?

No.

The TL-SG1008D does not provide Power over Ethernet.

It cannot directly power:

• IP cameras

• Wireless access points

• VoIP phones

• Other PoE devices

Use compatible PoE injectors or a PoE-enabled switch where required.

Is the TP-Link TL-SG1008D Managed?

No.

It is an unmanaged Gigabit switch.

There is no configurable VLAN interface, ACL management, centralized Omada control or Layer 3 routing.

This makes it ideal when the main requirement is simply adding more Gigabit Ethernet ports.

Does the TL-SG1008D Provide Wi-Fi?

No.

The TL-SG1008D is a wired Ethernet switch.

Wi-Fi must be provided by a wireless router or separate access point.

Does the TL-SG1008D Increase Internet Speed?

No.

A switch cannot increase the internet speed supplied by your ISP.

However, if you are replacing a Fast Ethernet switch, the TL-SG1008D can remove a previous 100Mbps wired bottleneck.

Does the TL-SG1008D Need a Router?

For normal internet access, the usual topology is:

Internet → Router → TL-SG1008D → Devices

The router provides functions such as NAT, DHCP, firewalling and internet routing.

The TL-SG1008D expands the number of available Ethernet connections.

Advantages and Limitations

Who Should Buy the TP-Link TL-SG1008D?

The TL-SG1008D is ideal for users who need up to eight Gigabit Ethernet connections without the complexity or expense of a managed switch.

It is especially suitable for:

• Homes

• Small offices

• Fibre internet

• Starlink

• Desktop computers

• Smart TVs

• Gaming consoles

• Network printers

• NAS systems

• NVRs

• Access points

• Small workgroups

Users requiring PoE, VLANs, centralized management or speeds above 1Gbps should consider a more advanced TP-Link switch.

Detailed TP-Link TL-SG1008D Specifications

TP-Link's US support page currently exposes hardware revisions ranging from V1 through V11.60, and the manufacturer explicitly notes that hardware-version availability varies by region. Exact power, dimensions and certain secondary specifications should therefore be checked against the revision supplied in Kenya.

What's Included in the Box?

A typical TL-SG1008D package includes:

Exact packaging can vary by market and hardware revision.

TP-Link TL-SG1008D Price in Kenya

Current Kenyan listings show the TP-Link TL-SG1008D around KES 3,100 excluding VAT at TDK, while current Jumia listings commonly range from approximately KES 3,540 to KES 4,500, with seller variation. 

These are third-party market references only, not Orbitlink Solutions' fixed selling price.

For the Orbitlink website, use:

Price: Contact Orbitlink Solutions for the current TP-Link TL-SG1008D 8-Port Gigabit Switch price in Kenya and stock availability.

Why Buy TP-Link TL-SG1008D from Orbitlink Solutions?

Orbitlink Solutions supplies TP-Link switches, routers, gateways, access points and related networking equipment for homes, SMEs and larger projects across Kenya.

Customers can get assistance choosing between Fast Ethernet, Gigabit, PoE, Omada managed, 2.5G and 10G switches depending on internet speed, number of devices, CCTV requirements, wireless access points, servers and planned future expansion.

Orbitlink Solutions can also assist with complete network designs involving Starlink, fibre internet, routers, Ethernet switches, Wi-Fi access points and structured cabling.

Watch: TP-Link 8-Port Gigabit Switch

The TP-Link TL-SG1008D provides a simple way to expand a wired network while retaining Gigabit Ethernet performance. Eight auto-negotiating ports allow Fast Ethernet and Gigabit equipment to operate together, while Auto MDI/MDIX eliminates much of the traditional complexity associated with Ethernet cabling.

Its Gigabit architecture is particularly useful for modern fibre and Starlink installations where a 100Mbps Fast Ethernet switch could become a bottleneck. The switch is also useful for NAS transfers, NVR traffic, gaming systems and high-performance wireless access points that benefit from Gigabit wired connectivity.

For customers who only need straightforward Gigabit network expansion, the TL-SG1008D offers an attractive balance of port count, simplicity and affordability. For installations requiring PoE, VLANs, centralized management or multi-Gigabit speeds, Orbitlink Solutions can supply a suitable TP-Link PoE or Omada managed alternative.

Frequently Asked Questions About TP-Link TL-SG1008D

What is the TP-Link TL-SG1008D?

The TL-SG1008D is an 8-port unmanaged Gigabit Ethernet desktop switch designed to expand a wired LAN without requiring configuration. 

How many Ethernet ports does the TL-SG1008D have?

It has eight 10/100/1000Mbps RJ45 ports. 

Is the TL-SG1008D Gigabit?

Yes. Each compatible port can establish a nominal Gigabit Ethernet link at up to 1Gbps.

What is the switching capacity?

Current Kenyan specifications list 16Gbps switching capacity. 

What is the packet-forwarding rate?

A current Kenya listing specifies 11.9 Mpps. 

Does TL-SG1008D require configuration?

No. It is plug-and-play. 

Does it support Auto MDI/MDIX?

Yes. All eight ports support Auto MDI/MDIX. 

Does TL-SG1008D support Jumbo Frames?

Documented TP-Link revisions support Jumbo Frames up to 15KB. 

Is the TL-SG1008D fanless?

Yes. It uses a fanless design.

Does TL-SG1008D support PoE?

No. It does not supply electrical power over Ethernet.

Can I use TL-SG1008D with fibre internet?

Yes. Its Gigabit ports make it suitable for modern fibre connections up to the Gigabit class, subject to router and device performance.

Can I use TL-SG1008D with Starlink?

Yes. It is well suited to distributing a Starlink Ethernet connection to multiple wired devices.

Can TL-SG1008D handle 500Mbps internet?

Yes, provided the router, cables and endpoint devices can also support the required throughput.

Can TL-SG1008D handle Gigabit internet?

It supports Gigabit Ethernet links. Actual application throughput will be somewhat below the nominal line rate because of protocol overhead.

Is TL-SG1008D suitable for NAS?

Yes. Gigabit Ethernet makes it significantly more suitable for NAS and local file transfers than a Fast Ethernet switch.

Can I connect an access point?

Yes. It can provide Gigabit data connectivity to an access point. If the AP requires PoE, use an injector or PoE switch.

Does TL-SG1008D provide Wi-Fi?

No. It is a wired switch.

Is TL-SG1008D managed?

No. It is an unmanaged switch.

What is the difference between TL-SF1008D and TL-SG1008D?

The TL-SF1008D is limited to 100Mbps per port, while the TL-SG1008D supports up to 1Gbps per port.

How many endpoint devices can I connect?

The switch has eight ports. If one is used as the uplink to the router, seven ports remain for other devices.

What is the TP-Link TL-SG1008D price in Kenya?

Current examples range around KES 3,100 ex VAT to approximately KES 4,500, depending on seller and VAT treatment. Contact Orbitlink Solutions for current stock and pricing. 

Buy TP-Link 8-Port Gigabit Switch in Kenya

The TP-Link TL-SG1008D 8-Port Gigabit Desktop Switch is an excellent choice for customers who need reliable high-speed Ethernet expansion without advanced configuration. Its eight Gigabit ports, Auto-Negotiation, Auto MDI/MDIX, flow control, fanless design, Green Ethernet and plug-and-play installation make it suitable for homes, small businesses, fibre and Starlink networks. 

Compared with an 8-port Fast Ethernet switch, the TL-SG1008D provides considerably more headroom for high-speed internet, local file transfers, NAS storage, CCTV traffic and modern wired devices.

Contact Orbitlink Solutions

Orbitlink Solutions
Lyric House, Kimathi Street, Nairobi
Phone: +254 743 720 551
Email: info@orbitlinksolutions.co.ke
Hours: Monday–Saturday, 9:00 AM–6:00 PM
Availability: Nairobi pickup and nationwide delivery

Contact Orbitlink Solutions for the current TP-Link TL-SG1008D 8-Port Gigabit Switch price in Kenya, TP-Link unmanaged switches, PoE switches, Omada managed switches, routers, access points and complete fibre or Starlink networking solutions.